Revision #1

This IPv6 Test Lab Extension describes how to configure DHCPv6 for the Contoso intranet. You configure DC1 as a DHCPv6 server and modify its role as an advertising router for the Corpnet and Corpnet2 subnets.

Note  These instructions are designed for a working IPv6 test lab that has been configured based on the instructions in the Test Lab Guide: Demonstrate IPv6.

If you are running the IPv6 test lab in a virtual environment, you can create snapshots of the virtual machines (VMs) for all of the test lab computers before performing the following procedure.

Configuring and Demonstrating DHCPv6 for IPv6 Addresses and Settings
To configure DC1 as the DHCPv6 server:

1. On DC1, click Start, click All Programs, click Accessories, right-click Command Prompt, and then click Run as administrator.
2. In the Command Prompt window, type netsh interface ipv6 add address Corpnet 2001:db8:0:1::1111, and then press ENTER.
3. In the Command Prompt window, type netsh interface ipv6 add address Corpnet2 2001:db8:0:1::2222, and then press ENTER. The DHCP Server service needs static IPv6 addresses on its interfaces to service DHCPv6 requests from IPv6 hosts.
4. On DC1, click Start, point to Administrative Tools, and then click DHCP.
5. In the console tree of the DHCP snap-in, open dc1.corp.contoso.com, right-click IPv6, and then click New Scope.
6. On the Welcome page, click Next.
7. On the Scope Name page, type Corpnet in Name, and then click Next.
8. On the Scope Prefix page, type 2001:db8:0:1:: in Prefix, and then click Next.
9. On the Add Exclusions page, click Next.
10. On the Scope Lease page, click Next.
11. On the Completing page, click No in Activate Scope Now, and then click Finish.
12. In the console tree of the DHCP snap-in, right-click IPv6, and then click New Scope.
13. On the Welcome page, click Next.
14. On the Scope Name page, type Corpnet2 in Name, and then click Next.
15. On the Scope Prefix page, type 2001:db8:0:2:: in Prefix, and then click Next.
16. On the Add Exclusions page, click Next.
17. On the Scope Lease page, click Next.
18. On the Completing page, click No in Activate Scope Now, and then click Finish.
19. In the Command Prompt window, run the following commands:

    netsh interface ipv6 set route 2001:db8:0:1::/64 Corpnet publish=no

    netsh interface ipv6 set route 2001:db8:0:2::/64 Corpnet2 publish=no

    netsh interface ipv6 set interface Corpnet managedaddress=enable otherstateful=enable

    netsh interface ipv6 set interface Corpnet2 managedaddress=enable otherstateful=enable

1. Connect CLIENT1 to the Corpnet subnet.
2. In the Command Prompt window, type ipconfig, and then press ENTER. Notice that only a link-local address is assigned to the Local Area Connection adapter. DC1 is not advertising address prefixes and the DHCPv6 scope for the Corpnet is not yet active.
3. On DC1, in the console tree of the DHCP snap-in, right-click Scope [2001:db8:0:1::] Corpnet, and then click Activate.
4. In the console tree of the DHCP snap-in, right-click Scope [2001:db8:0:2::] Corpnet2, and then click Activate.

To demonstrate the use of DHCPv6 by CLIENT1:

1. Connect CLIENT1 to the Corpnet2 subnet.
2. In the Command Prompt window, type ipconfig, and then press ENTER.
3. Notice that an IPv6 address beginning with "2001:db8:0:2" is assigned to the Local Area Connection adapter.
4. In the Command Prompt window, type ipconfig /all, and then press ENTER.
5. Notice the Lease Obtained and Lease Expires fields after the IPv6 address beginning with "2001:db8:0:2". This indicates that this address was assigned by a DHCPv6 server.
6. In the Command Prompt window, type ipconfig /renew6, and then press ENTER.
7. In the Command Prompt window, type ipconfig /all, and then press ENTER.
8. Notice the Lease Obtained and Lease Expires fields after the IPv6 address beginning with "2001:db8:0:2" has changed from step 28.
9. Notice that 10.0.0.1 is the only DNS server assigned to the Local Area Connection adapter.
10. On DC1, in the DHCP snap-in, right-click Server Options, and then click Configure Options.
11. On the General tab, select 0023 DNS Recursive Name Server IPv6 Addresses, type 2001:db8:0:1::1111 in New IPv6 address, click Add, and then click OK.
12. In the Command Prompt window, type ipconfig /renew6, and then press ENTER.
13. In the Command Prompt window, type ipconfig /all, and then press ENTER. Notice that the DNS servers assigned to the Local Area Connection adapter now includes 2001:db8:0:1::1111.

With this new configuration, CLIENT1 can obtain native IPv6 addresses on the Contoso intranet without relying on the router advertisements sent by the native IPv6 router for the Corpnet and Corpnet2 subnets (DC1). CLIENT1 can also obtain the IPv6 address of its DNS server (DC1). Notice that CLIENT1 is still configuring its default router from the router advertisements sent by the native IPv6 router (DC1). There is no DHCPv6 option to configure the default gateway.

If you are running the IPv6 test lab in a virtual environment, you can discard the changes made by these procedures by restoring the previously made snapshots of the VMs for all of the computers in the test lab. Alternately, if you would like return to this working configuration using DHCPv6, you can create a new set of snapshots before restoring the previously made snapshots.

To manually restore the configuration of the IPv6 test lab, perform the following procedure.

Restoring the IPv6 Test Lab
To restore the IPv6 test lab to its original configuration:

1. On DC1, in the Command Prompt window, run the following commands:

   netsh interface ipv6 del address Corpnet 2001:db8:0:1::1111

   netsh interface ipv6 del address Corpnet2 2001:db8:0:1::2222

   netsh interface ipv6 set interface Corpnet managedaddress=disable otherstateful=disable

   netsh interface ipv6 set interface Corpnet2 managedaddress=disable otherstateful=disable

   netsh interface ipv6 set route 2001:db8:0:1::/64 Corpnet publish=yes

   netsh interface ipv6 set route 2001:db8:0:2::/64 Corpnet2 publish=yes

2. In the DHCP console tree, click Server Options.
3. In the details pane, right-click 00023 DNS Recursive Name, click Delete, and then click OK.
4. In the DHCP console tree, right-click Scope [2001:db8:0:1::] Corpnet, click Delete, and then click Yes twice.
5. In the DHCP console tree, right-click Scope [2001:db8:0:2::] Corpnet2, click Delete, and then click Yes twice.